Subaru outback draw tite hitch installation

Subaru outback draw tite hitch installation install#
Subaru outback draw tite hitch installation driver#

DonвЂ™t have the time to install yourself? Schedule a professional installation at and weвЂ™ll do the work. Whatever vehicle you drive, we have a trailer hitch for you. You should now have your Draw-Tite 75673 trailer hitch installed on your Subaru Outback. from the end of the receiver to the end of the bumper from the pin hole to the end of the bumper from the inside of the receiver the ground Remove the strap or rope used for support. Be sure that all six are reattached and that they are firmly in place. This can be done by hand or using exhaust pliers. Raise the exhaust system by reattaching the isolator rods to the rubber hangers. Return the heat shieldsДЄfter both heat shields have been trimmed, reattach them to the frame using the 10mm socket or Philips screwdriver and the same bolts that were in place previously. The heat shield should be able to fit flush against the hitch bracket with the nut in place. Using the tin snips, cut away the rectangular area near the forward attachment bolt.

With the hitch firmly secured, the heat shields must be trimmed to fit above the exhaust mufflers. The wrench should make a clicking sound when it has reached the correct amount of torque. With the hitch in position, remove the fish wire, then attach the conical washers and hex nuts to the bolts and tighten them by hand. You will need to thread the fish wire through the holes on the hitch. Lift the hitch into position, lining up the bolts and the attachment holes. Tape the provided flat washers over the forward attachment holes on both sides of the hitch. Use the larger spacers for the forward attachment holes and the small spacers for the rear holes. Repeat this step for all other hitch attachment holes. Attach the carriage bolt and large spacer to the fish wire coil and pull it back through the access hole so the bolt thread drops through the attachment hole and the spacer is between the frame and bolt head. Thread the fish wire through the hitch attachment hole and out of the access hole. Thread carriage bolts through the access holes The access holes will be used to fish-wire the provided carriage bolts into the hitch attachment holes.

Subaru outback draw tite hitch installation driver#

Using the 1 ?-inch hole saw, drill an access hole in the frame on the driver and passenger side roughly two inches from the forwardmost plug hole. Take out the rubber plugs from the holes on the bottom of the frame after the heat shields are removed. Save the bolts, as you will be reinstalling the heat shields after the hitch is installed. Use a 10mm socket or Phillips head screwdriver to remove the heat shields found above each muffler. You may need to use soapy water to loosen the rods. There are two above each exhaust muffler and another above the center exhaust pipe. Remove the isolator rods from the rubber exhaust hangers using the exhaust pliers. Make sure the strap or rope can be adjusted. First off, the design is minimal, and the installation is easy, with only a handful of moving pieces that you need to use. There were a few things that drew us to this hitch receiver. Tie a rope or strap around the center exhaust pipe and attach it to a sturdy engine component under the body, like a crossmember. The final suggestion is the Draw-Tite 75673 Max-Frame Receiver. Subaru Outback (2010-2018) hitch installation steps 1. making it capable of hauling small and large loads. The hitch has a max trailer weight of 4,000 lb. The Draw-Tite 75673 is a class 3, bolt-on trailer hitch designed for the 2018 Subaru Outback. Follow these basic steps to begin hauling all kinds of hitch-mounted accessories with your Subaru Outback today. Installing a trailer hitch on a 2018 Subaru Outback requires a few tools, a Draw-Tite 75673 custom trailer hitch and about 45 minutes to complete the installation. Move-In Online Today! Move-In Online: Get Started.tongue weight.ДO NOT exceed the tow weight of actual vehicle tow hitch. New hitch receiver towing rate is 3500 lbs. Works best with a oem 4 1/2вЂќ standard hitch or bigger. MUST HAVE A Draw-Tite Hitch Carrier 2' Class III Hitch Receiver or Curt Class 3 Hitch for the 2018-2019 Crosstrek Available HEREДЄdditional 2вЂќ Receiver and Swing-Out Receiver total making it very convenient to open, with their no-wobble technology. All with keeping the same Rigid Armor look. Rigid added a molly panel for multiple mounting solutions for your Shovel, Fold-out table, or even roto pax gas tank. Designed by Rigid Armor and engineered for lighter vehicles, this Subaru Crosstrek Hybrid Swing Out has a 2' Hitch, which helps to carry all your camping essentials on every adventure.